Stratclad Walling With S-Lock
Stratco
SKU: SCLWSL42CR
About this product
Featuring the S-Lock system that makes joining sheets quick, neat and easy. With a wide coverage, this versatile wall cladding is ideal for a range of applications.Image gallery
Stratclad Wall Cladding
Wide profile wall cladding with the innovative S-Lock joining system.
Stratclad is a versatile wall cladding material suitable for a variety of applications. The wide coverage of 870mm saves you time and money as less sheets are required to cover the chosen area.
The innovative S-Lock system features a specialised notch in one edge of the sheet for the proceeding edge to slot into. This makes installation quick, easy and neat.
Available Colours
Brochures & Installation Guides
BMT 0.35mm & 0.42mm
Tolerance L ±5mm W ±2mm
Material Specifications
| Material Specifications | ||||
| Material Properties | 0.35mm BMT | 0.42mm BMT | ||
|---|---|---|---|---|
| Zinc/Al | Colour | Zinc/Al | Colour | |
| Total Coated Thickness (mm) | 0.40 | 0.43 | 0.47 | 0.50 |
| Mass (kg/linear metre) | 2.74 | 2.79 | 3.26 | 3.32 |
| Mass (kg/square metre) | 3.15 | 3.22 | 3.75 | 3.81 |
| Yield (square metre/tonne) | 317.2 | 310.8 | 267.0 | 262.4 |
| Tensile Strength (MPa) | G550 | G550 | G550 | G550 |
Maximum Recommended Spans For Walling (mm)
Determined by wind speeds for non-cyclonic areas
| Maximum Recommended Spans for Walling (mm) | ||||||
| Span Type | 0.35mm BMT | 0.42mm BMT | ||||
|---|---|---|---|---|---|---|
| N1 (W28) | N2 (W33) | N3 (W41) | N1 (W28) | N2 (W33) | N3 (W41) | |
| Single | 650 | 550 | 350 | 800 | 700 | 500 |
| End | 750 | 650 | 500 | 900 | 800 | 650 |
| Internal | 750 | 650 | 500 | 900 | 800 | 650 |
| Overhang | 100 | 100 | 100 | 150 | 150 | 150 |
Values applicable for use with steel supports of minimum 0.75mm thickness, G550.
Note: For Stratclad design parameters and span definitions, please refer to the Engineering notes at the beginning of the Roofing and Walling section.
For Region C and D fixings refer to ‘Cyclonic Cladding’ within the roofing and walling ‘Cladding’ section of the Stratco website.
Note: The following recommendations apply to non-cyclonic areas.
- All fasteners must have neoprene washers to prevent water penetration.
- Side lap fixing is recommended at no greater than 300mm centres for external applications. For internal applications where support spacings exceed 1000mm it is recommended side laps are fastened mid-span.
- Use either 8x12mm self drill stitching screws (with seal) or 3.2mm sealed blind rivets.
- If fixing over an insulation blanket the next standard screw length to that indicated may be required with minimum 25mm timber embedment to be maintained.
Wall Laying Procedure
Prevailing Wind →
← Laying Direction
Fastener Selection
Fixing to Steel
10 x 16mm self drilling and tapping screw with neoprene washer
Fixing to Timber
10 x 25mm type 17 hex head screw with neoprene washer
Fastener Positions
Walling Fastener Location
