has been added to your cart
View Cart

Flashings

SKU: Flashings

Stratco can fold a wide range of standard or custom flashings to suit your requirements. Flashings are available in pre-painted steel, zinc/al, aluminium, stainless steel, and copper. Choose from a wide range of available thicknesses from 0.4mm to 3.0mm depending on your state. Whether you want to install it yourself or require assistance, we are here to help. Contact us for pricing and further details today.
Available in QLD

Order your Stratco flashings in a flash!

Flashings Design App

NEW Flashing Design Tool

Order a flashing using the designer today, and have it by tomorrow ... No fuss!

Whether you are on-site, on a roof, or in your office, you can order your flashings direct with Stratco using your desktop, phone or tablet.

 

Flashing Designer

Box Gutters

A square or rectangular gutter that is used within the boundaries of the roof. It may be formed between a roof surface and a parapet wall or between two roof surfaces. Available with infold, outfold, splashback and squashfold edges. This gutter is usually supported on a box gutter board to improve strength and stiffness and to minimise damage caused by roof traffic.

Flashings Roof Flashing Box Gutter

1

Flashings Roof Flashing Tapered Drawing Standard Box Gutter

Standard Box Gutter

2

Flashings Roof Flashing Tapered Drawing Box Gutter With Single Outfold

Box Gutter
With Single Outfold

3

Flashings Roof Flashing Tapered Drawing Angled Box Gutter

Angled Box Gutter

4

Flashings Roof Flashing Tapered Drawing Box Gutter With Double Splashbacks

Box Gutter
With Double Splashbacks

5

Flashings Roof Flashing Tapered Drawing Box Gutter With Single Splashbacks

Box Gutter
With Single Splashback

6

Flashings Roof Flashing Tapered Drawing Box Gutter With Double Infolds

Box Gutter
With Double Infolds

7

Flashings Roof Flashing Tapered Drawing Box Gutter With Double Splay

Box Gutter
With Double Splay

8

Flashings Roof Flashing Tapered Drawing Box Gutter With Squashfolds

Box Gutter
With Squashfolds

9

Flashings Roof Flashing Tapered Drawing Box Gutter With Double Outfolds

Box Gutter
With Double Outfolds

10

Flashings Roof Flashing Tapered Drawing Box Gutter With Double Upturns

Box Gutter
With Double Upturns

11

Flashings Roof Flashing Tapered Drawing Box Gutter With Single Upturns

Box Gutter
With Single Upturns

12

Flashings Roof Flashing Tapered Drawing Box Gutter With 'V' Stiffening Rib

Box Gutter
With 'V' Stiffening Rib

Industrial Eave Gutters

A purpose made external gutter which is located at the edge of an industrial roof. It is usually supported by heavy gauge brackets that have been designed specifically to suit the industrial eaves gutter shape. When made in larger sizes special attention should be given to minimising oil canning of flat surfaces by adding extra ribs into the design.

Flashings Roof Flashing Industrial Eaves Gutter

13

Flashings Roof Flashing Tapered Drawing Industrial Eaves Gutter With Return

Industrial Eaves Gutter
With Return

14

Flashings Roof Flashing Tapered Drawing Basic Industrial Eaves Gutter

Basic Industrial
Eaves Gutter

15

Flashings Roof Flashing Tapered Drawing Industrial Eaves With Outfold

Industrial Eaves
With Outfold

16

Flashings Roof Flashing Tapered Drawing Industrial Eaves With Stiffening Rib

Industrial Eaves
With Stiffening Rib

17

Flashings Roof Flashing Tapered Drawing Industrial Eaves Gutter With Bead

Industrial Eaves Gutter
With Bead

18

Flashings Roof Flashing Tapered Drawing Fancy Industrial Eaves Gutter With Bead

Fancy Industrial Eaves
Gutter With Bead

19

Flashings Roof Flashing Tapered Drawing Two Rib Industrial Eaves Gutter

Two Rib Industrial
Eaves Gutter

20

Flashings Roof Flashing Tapered Drawing Industrial Eaves Gutter With Splay And Outfold

Industrial Eaves Gutter
With Splay And Outfold

21

Flashings Roof Flashing Tapered Drawing Industrial Eaves Gutter With Protruding Rib

Industrial Eaves Gutter
With Protruding Rib

Valley Gutters

A shallow gutter formed to suit the angle between two internal slopes of a roof. Its design will usually include a return at each edge to minimise the possibility of water spillage into the roof space. Depending on the size and application additional internal stiffening ribs may be included.

Flashings Roof Flashing Valley Gutter

22

Flashings Roof Flashing Tapered Drawing Standard Valley

Standard Valley

23

Flashings Roof Flashing Tapered Drawing Valley With Upstands

Valley With Upstands

24

Flashings Roof Flashing Tapered Drawing Valley With Squashfolds

Valley With Squashfolds

25

Flashings Roof Flashing Tapered Drawing Segmented Valley

Segmented Valley

26

Flashings Roof Flashing Tapered Drawing Segmented Valley With Upstand

Segmented Valley
With Upstand

18

Flashings Roof Flashing Tapered Drawing Deep Valley With Square Ribs

Deep Valley
With Square Ribs

Trough Gutters

A half round segmented gutter formed into a trough. It is formed between a roof surface and a parapet wall or between two roof surfaces and is available with infold, outfold, splashback and squashfold edges. Usually supported by heavy gauge straps, trough gutters are very efficient and have better self cleaning properties than box gutters. In most cases the depth will not exceed half the width.

Flashings Roof Flashing Trough Gutter

28

Flashings Roof Flashing Standard Drawing Segmented Trough Gutter with Outfold

Segmented Trough
Gutter with Outfold

29

Flashings Roof Flashing Standard Drawing Standard Segmented  Trough Gutter

Standard Segmented
Trough Gutter

30

Flashings Roof Flashing Tapered Drawing Segmented Trough Gutter With Splashback

Segmented Trough
Gutter With Splashback

31

Flashings Roof Flashing Standard Drawing Part Segmented  Trough Gutter

Part Segmented
Trough Gutter

32

Flashings Roof Flashing Tapered Drawing Segmented Eaves Gutter With Standard Bead

Segmented Eaves Gutter
With Standard Bead

33

Flashings Roof Flashing Tapered Drawing Segmented Trough Gutter With Modified Bead

Segmented Trough Gutter
With Modified Bead

34

Flashings Roof Flashing Tapered Drawing Segmented Trough Gutter With Modified Splashbacks

Segmented Trough Gutter
With Modified Splashbacks

35

Flashings Roof Flashing Tapered Drawing Segmented Trough Gutter With Standard Splashbacks

Segmented Trough Gutter
With Standard Splashbacks

36

Flashings Roof Flashing Tapered Drawing Segmented Trough Gutter With Outfold & Raised Side

Segmented Trough Gutter
With Outfold & Raised Side

37

Flashings Roof Flashing Tapered Drawing Segmented Trough Gutter With Double Outfolds

Segmented Trough Gutter
With Double Outfolds

38

Flashings Roof Flashing Tapered Drawing Segmented Trough Gutter With Raised Sides

Segmented Trough Gutter
With Raised Sides

39

Flashings Roof Flashing Tapered Drawing Segmented Quad Gutter

Segmented
Quad Gutter

Corner Flashings

A folded piece of steel used for waterproofing wall sheeting where two walls meet to form an external corner. Where used with steel sheet walling it should lap at least one rib and a recommended two ribs for maximum water proofing.

Flashings Roof Flashing Corner

40

Flashings Roof Flashing Tapered Drawing Standard Corner Flashing

Standard Corner Flashing

41

Flashings Roof Flashing Tapered Drawing Square Corner Flashing

Square Corner Flashing

42

Flashings Roof Flashing Tapered Drawing Offset Corner Flashing

Offset Corner Flashing

43

Flashings Roof Flashing Tapered Drawing Modified Corner Flashing

Modified Corner Flashing

44

Flashings Roof Flashing Tapered Drawing Standard Internal Corner Flashing

Standard Internal
Corner Flashing

45

Flashings Roof Flashing Tapered Drawing Internal Corner With Internal Squash Fold

Internal Corner With
Internal Squash Fold

46

Flashings Roof Flashing Tapered Drawing Internal Corner With External Squash Fold

Internal Corner With
External Squash Fold

47

Flashings Roof Flashing Tapered Drawing Bulky Corner Flashing

Bulky Corner Flashing

48

Flashings Roof Flashing Tapered Drawing Stepped Corner Flashing

Stepped Corner Flashing

Apron Flashings

A folded piece of steel used to prevent water from penetrating the space where a vertical surface intersects a roof. Where used with steel sheet roofing it should lap at least one rib and a recommended two ribs for maximum water proofing. Wider apron flashings are advised when the base of the flashing faces into the prevailing wind.

Flashings Roof Flashing Apron

49

Flashings Roof Flashing Tapered Drawing Apron Flashing

Apron Flashing

50

Flashings Roof Flashing Tapered Drawing Apron Flashing With 90° Turndown

Apron Flashing
With 90° Turndown

51

Flashings Roof Flashing Tapered Drawing Apron Flashing With Pole Plate And 135° Break

Apron Flashing With
Pole Plate And 135° Break

52

Flashings Roof Flashing Tapered Drawing Apron Flashing With Pole Plate And 90° Break

Apron Flashing With
Pole Plate And 90° Break

53

Flashings Roof Flashing Tapered Drawing Apron Flashing With Splayed Pole Plate

Apron Flashing With
Splayed Pole Plate

54

Flashings Roof Flashing Tapered Drawing Side Flashing With Pole Plate

Side Flashing
With Pole Plate

Foot Moulds

A folded piece of steel used to finish the base of a vertical surface, in such a way as to prevent water penetration. It also provides an edge to an adjoining soffit. Typical applications are in facades and to finish overhanging canopies. The flashing also prevents water contact to the ends of sheeting.

Flashings Roof Flashing Foot Mould

55

Flashings Roof Flashing Tapered Drawing Standard Foot Mould

Standard Foot Mould

56

Flashings Roof Flashing Tapered Drawing Foot Mould With Squashfold

Foot Mould With Squashfold

57

Flashings Roof Flashing Tapered Drawing Square Foot Mould

Square Foot Mould

Pole Plate Flashings

A purpose made flashing used to seal the join between the end of a roof and masonry wall. A “V” groove end locates into either a preformed reglet, or a cut in the masonry wall providing a water resistant join to the roof and wall connection. When installed, pole plate flashings (often called chimney flashings) can either be stepped to conform to brick courses or left straight, for a more modern appearance.

Flashings Roof Flashing Pole Plate

58

Flashings Roof Flashing Tapered Drawing Pole Plate Flashing

Pole Plate Flashing

59

Flashings Roof Flashing Tapered Drawing Pole Plate Flashing With 90° Break

Pole Plate Flashing
With 90° Break

60

Flashings Roof Flashing Tapered Drawing Pole Plate Flashing With 135° Break

Pole Plate Flashing
With 135° Break

Sill Flashings

A steel sheet used to cap building framework and external brickwork at the base of a window or door frame. It also prevents water from pooling in these areas.

Flashings Roof Flashing Sill

61

Flashings Roof Flashing Tapered Drawing Sloping Sill Flashing

Sloping Sill Flashing

62

Flashings Roof Flashing Tapered Drawing Square Sill Flashing

Square Sill Flashing

63

Flashings Roof Flashing Tapered Drawing Square Sill Flashing With Return

Square Sill Flashing
With Return

64

Flashings Roof Flashing Tapered Drawing Z Flashing With Offset

Z Flashing With Offset

65

Flashings Roof Flashing Tapered Drawing Plain Sill Flashing

Plain Sill Flashing

66

Flashings Roof Flashing Tapered Drawing Sill Flashing With Drip Edge

Sill Flashing
With Drip Edge

Ridge Flashings

A steel covering over the ridge to provide a continuous cover and effective weather seal between two slopes. The size of the edge break should conform with the rib height of the steel roofing to which the ridge is attached. Good roofing practice is to notch this edge break to neatly fit around each rib of the roof sheet.

Flashings Roof Flashing Ridge

67

Flashings Roof Flashing Tapered Drawing Cover Flashing

Cover Flashing

68

Flashings Roof Flashing Tapered Drawing 3 Break Ridge Flashing

3 Break
Ridge Flashing

69

Flashings Roof Flashing Tapered Drawing Raised Top Ridge

Raised Top Ridge

Chimney Flashings

A folded steel sheet commonly used to provide a weather sealed base around chimneys to prevent water penetration. It is often made as a two piece flashing to provide flexibility in installation.

Flashings Roof Flashing Chimney

70

Flashings Roof Flashing Tapered Drawing Standard Chimney Flashing

Standard
Chimney Flashing

71

Flashings Roof Flashing Tapered Chimney Flashing With Splay

Chimney Flashing
With Splay

72

Flashings Roof Flashing Tapered Drawing Chimney Flashing With Outfold

Chimney Flashing
With Outfold

73

Flashings Roof Flashing Tapered Drawing Chimney Flashing With Pole Plate

Chimney Flashing
With Pole Plate

74

Flashings Roof Flashing Tapered Drawing Chimney Flashing With Box Gutter

Chimney Flashing
With Box Gutter

75

Flashings Roof Flashing Tapered Drawing Chimney Flashing And Cap

Chimney Flashing
And Cap

Parapet Capping

A covering used to waterproof and cap the ends of vertical sheets or masonry walls. A stiffening edge or break is often applied to the legs of the parapet cap for a more appealing appearance, and to minimise oilcanning of the steel. Ensure that these recommendations are taken into account when measuring the flashing. It is also important to ensure that water does not pool on top of the cap, to prevent water seeping into the building.

Flashings Roof Flashing Parapet Capping

76

Flashings Roof Flashing Tapered Drawing Standard Parapet Capping With Chamfer

Standard Parapet
Capping With Chamfer

77

Flashings Roof Flashing Tapered Drawing Standard Parapet Capping

Standard
Parapet Capping

78

Flashings Roof Flashing Tapered Drawing Standard Parapet Capping With Return Hooks

Standard Parapet Capping
With Return Hooks

79

Flashings Roof Flashing Tapered Drawing Parapet Capping With Fold One Side

Parapet Capping
With Fold One Side

80

Flashings Roof Flashing Tapered Drawing Parapet Capping With Hook One Side

Parapet Capping
With Hook One Side

81

Flashings Roof Flashing Tapered Drawing Parapet Capping With Hook And Overflashing

Parapet Capping With
Hook And Overflashing

82

Flashings Roof Flashing Tapered Drawing Parapet Cap With ´V´ Both Sides

Parapet Cap With
´V´ Both Sides

83

Flashings Roof Flashing Tapered Drawing Parapet Cap with ´V´ One Side

Parapet Cap with
´V´ One Side

84

Flashings Roof Flashing Tapered Drawing Combined Parapet And Apron Flashing

Combined Parapet
And Apron Flashing

85

Flashings Roof Flashing Tapered Drawing Angled Combined Parapet And Apron Flashing

Angled Combined Parapet
And Apron Flashing

86

Flashings Roof Flashing Tapered Drawing Angled combined Parapet And Apron With 90° Break

Angled combined Parapet
And Apron With 90° Break

87

Flashings Roof Flashing Tapered Drawing Combined Parapet And Apron With break

Combined Parapet
And Apron With break

Barge Capping

A folded sheet used to waterproof the junction between a fascia or barge board and roof sheeting. The size of the edge break should conform with the rib height of the steel roofing to which the ridge is attached.

Flashings Roof Flashing Barge Capping

88

Flashings Roof Flashing Tapered Drawing Standard Square Barge Cap

Standard Square
Barge Cap

89

Flashings Roof Flashing Tapered Drawing Standard Barge Cap With 90° Break

Standard Barge
Cap With 90° Break

90

Flashings Roof Flashing Tapered Drawing Barge With Hook But No Break

Barge With Hook
But No Break

91

Flashings Roof Flashing Tapered Drawing Barge With Hook

Barge With Hook

92

Flashings Roof Flashing Tapered Drawing Barge With ´V´

Barge With ´V´

93

Flashings Roof Flashing Tapered Drawing Angled Barge With 90° Break

Angled Barge
With 90° Break

94

Flashings Roof Flashing Tapered Drawing Angled Barge With 135° Break

Angled Barge With
135° Break

95

Flashings Roof Flashing Tapered Drawing Garage Barge

Garage Barge

96

Flashings Roof Flashing Tapered Drawing Square Top Barge

Square Top Barge

97

Flashings Roof Flashing Tapered Drawing Square Top Barge With 90° Break

Square Top Barge
With 90° Break

98

Flashings Roof Flashing Tapered Drawing Square Top Barge With Drip Edge

Square Top Barge
With Drip Edge

99

Flashings Roof Flashing Tapered Drawing Simple Barge With 90° Break

Simple Barge
With 90° Break

Miscellaneous Flashings

100

Flashings Roof Flashing Tapered Drawing Overcap

Overcap

101

Flashings Roof Flashing Tapered Drawing Standard Back Channel

Standard Back Channel

102

Flashings Roof Flashing Tapered Drawing Fascia Capping

Fascia Capping

Flashing Materials

Stratco flashings are available in galvanised, unpainted zinc/al, pre-painted colour steel, aluminium, stainless steel, and copper. They can be folded in a wide selection of gauges, ranging from 0.4mm to 3.0mm. The availability of gauges may vary between states.

Material Base Metal Thickness (mm)
Galvanised 0.40* 0.55* 0.80* 1.00* 1.20* 1.60** 2.00† 3.00†
Zinc/al 0.40* 0.55* 0.80* 1.00* 1.20* - - -
Colour 0.40* 0.55* - - - - - -
Ultra - 0.55* - - - - - -
Alum (Mill Finish) - - - 1.00# 1.20 - - -
Stainless Steel
304/2B (NT)
0.55 - 0.90 - 1.20 1.60 Not available in all
states. Please check
prior to ordering.
Stainless Steel
316/2B (SA)
0.55 0.70* 0.90 - 1.20 1.60

* Maximum length 8000mm, ** Maximum length 6000mm, † Maximum length 2400mm, # Maximum length 4000mm Note: Maximum coil width 1200mm.

Receiving Orders

Stratco prefer to receive orders by fax or by Stratco Direct™. Stratco will accept, but take no responsibility for orders placed by phone.


Flashing Drawings

Standard Flashings

Flashings Roof Flashing Ordering Standard

When drawing standard flashings, letters describe the dimensions of each plane on the flashing, and numbers describe the included angle. You need to advise us of all dimensions, and identify any angle that is not 90 degrees.

Tapered Flashings

Flashings Roof Flashing Ordering Tapered

Tapered flashings use the same system as non-tapered flashings. Angles will always be constant throughout the flashing. The dimensions closest to you described as 'NEAR' (as shown in the drawing) have a '1' added to the letter representing the dimension, and the dimensions furthest away described as 'FAR' have the number '2'. Box gutter (1) would therefore be described as shown in the diagram on the right.

Order Methods

Clock Method For Placing Orders By Phone

Flashings Roof Flashing Ordering Clock

Commence at the centre of the clock. Draw a straight line from the centre to the number on the clock (1-12) at the required angle, representing the first line of your flashing drawing. Where the pen stops becomes the centre of the clock for the next line. Complete the flashing using this method. For tapered flashings quote nearest edges first. Repeat for the back (use the same letters) unless otherwise indicated.

Page Drawing Method

Flashings Roof Flashing Ordering Page

Begin drawing the flashing at the centre of the page. Describe the direction of the line as you draw it. Advise if the line moves vertically up or down the page, horizontally left or right, or to which page corner. Advise the length of the line. Do this for every line in the flashing. Advise of any included angles.


Flashing Profiles

Box Gutters

A square or rectangular gutter that is used within the boundaries of the roof. It may be formed between a roof surface and a parapet wall or between two roof surfaces. Available with infold, outfold, splashback and squashfold edges. This gutter is usually supported on a box gutter board to improve strength and stiffness and to minimise damage caused by roof traffic.

Flashings Roof Flashing Box Gutter

1

Flashings Roof Flashing Standard Drawing Standard Box Gutter

Standard Box Gutter

2

Flashings Roof Flashing Standard Drawing Box Gutter With Single Outfold

Box Gutter
With Single Outfold

3

Flashings Roof Flashing Standard Drawing Angled Box Gutter

Angled Box Gutter

4

Flashings Roof Flashing Standard Drawing Box Gutter With Double Splashbacks

Box Gutter
With Double Splashbacks

5

Flashings Roof Flashing Standard Drawing Box Gutter With Single Splashbacks

Box Gutter
With Single Splashback

6

Flashings Roof Flashing Standard Drawing Box Gutter With Double Infolds

Box Gutter
With Double Infolds

7

Flashings Roof Flashing Standard Drawing Box Gutter With Double Splay

Box Gutter
With Double Splay

8

Flashings Roof Flashing Standard Drawing Box Gutter With Squashfolds

Box Gutter
With Squashfolds

9

Flashings Roof Flashing Standard Drawing Box Gutter With Double Outfolds

Box Gutter
With Double Outfolds

10

Flashings Roof Flashing Standard Drawing Box Gutter With Double Upturns

Box Gutter
With Double Upturns

11

Flashings Roof Flashing Standard Drawing Box Gutter With Single Upturns

Box Gutter
With Single Upturns

12

Flashings Roof Flashing Standard Drawing Box Gutter With 'V' Stiffening Rib

Box Gutter
With 'V' Stiffening Rib

Industrial Eave Gutters

A purpose made external gutter which is located at the edge of an industrial roof. It is usually supported by heavy gauge brackets that have been designed specifically to suit the industrial eaves gutter shape. When made in larger sizes special attention should be given to minimising oil canning of flat surfaces by adding extra ribs to the design.

Flashings Roof Flashing Industrial Eaves Gutter

13

Flashings Roof Flashing Standard Drawing Industrial Eaves Gutter With Return

Industrial Eaves Gutter
With Return

14

Flashings Roof Flashing Standard Drawing Basic Industrial Eaves Gutter

Basic Industrial
Eaves Gutter

15

Flashings Roof Flashing Standard Drawing Basic Industrial Eaves With Outfold

Industrial Eaves
With Outfold

16

Flashings Roof Flashing Standard Drawing Basic Industrial Eaves With Stiffening Rib

Industrial Eaves
With Stiffening Rib

17

Flashings Roof Flashing Standard Drawing Industrial Eaves Gutter With Bead

Industrial Eaves Gutter
With Bead

18

Flashings Roof Flashing Standard Drawing Fancy Industrial Eaves Gutter With Bead

Fancy Industrial Eaves
Gutter With Bead

19

Flashings Roof Flashing Standard Drawing Two Rib Industrial Eaves Gutter

Two Rib Industrial
Eaves Gutter

20

Flashings Roof Flashing Standard Drawing Industrial Eaves Gutter With Splay And Outfold

Industrial Eaves Gutter
With Splay And Outfold

21

Flashings Roof Flashing Standard Drawing Industrial Eaves Gutter With Protruding Rib

Industrial Eaves Gutter
With Protruding Rib

Valley Gutters

A shallow gutter formed to suit the angle between two internal slopes of a roof. Its design will usually include a return at each edge to minimise the possibility of water spillage into the roof space. Depending on the size and application additional internal stiffening ribs may be included.

Flashings Roof Flashing Valley Gutter

22

Flashings Roof Flashing Standard Drawing Standard Valley

Standard Valley

23

Flashings Roof Flashing Standard Drawing Valley With Upstands

Valley With Upstands

24

Flashings Roof Flashing Standard Drawing Valley With Squashfolds

Valley With Squashfolds

25

Flashings Roof Flashing Standard Drawing Segmented Valley

Segmented Valley

26

Flashings Roof Flashing Standard Drawing Segmented Valley With Upstand

Segmented Valley
With Upstand

18

Flashings Roof Flashing Standard Drawing Deep Valley With Square Ribs

Deep Valley
With Square Ribs

Trough Gutters

A half round segmented gutter formed into a trough. It is formed between a roof surface and a parapet wall or between two roof surfaces and is available with infold, outfold, splashback and squashfold edges. Usually supported by heavy gauge straps, trough gutters are very efficient and have better self cleaning properties than box gutters. In most cases the depth will not exceed half the width.

Flashings Roof Flashing Trough Gutter

28

Flashings Roof Flashing Standard Drawing Segmented Trough Gutter with Outfold

Segmented Trough
Gutter with Outfold

29

Flashings Roof Flashing Standard Drawing Standard Segmented Trough Gutter

Standard Segmented
Trough Gutter

30

Flashings Roof Flashing Standard Drawing Segmented Trough Gutter With Splashback

Segmented Trough
Gutter With Splashback

31

Flashings Roof Flashing Standard Drawing Part Segmented Trough Gutter

Part Segmented
Trough Gutter

32

Flashings Roof Flashing Standard Drawing Segmented Eaves Gutter With Standard Bead

Segmented Eaves Gutter
With Standard Bead

33

Flashings Roof Flashing Standard Drawing Segmented Trough Gutter With Modified Bead

Segmented Trough Gutter
With Modified Bead

34

Flashings Roof Flashing Standard Drawing Segmented Trough Gutter With Modified Splashbacks

Segmented Trough Gutter
With Modified Splashbacks

35

Flashings Roof Flashing Standard Drawing Segmented Trough Gutter With Standard Splashbacks

Segmented Trough Gutter
With Standard Splashbacks

36

Flashings Roof Flashing Standard Drawing Segmented Trough Gutter With Outfold & Raised Side

Segmented Trough Gutter
With Outfold & Raised Side

37

Flashings Roof Flashing Standard Drawing Segmented Trough Gutter With Double Outfolds

Segmented Trough Gutter
With Double Outfolds

38

Flashings Roof Flashing Standard Drawing Segmented Trough Gutter With Raised Sides

Segmented Trough Gutter
With Raised Sides

39

Flashings Roof Flashing Standard Drawing Segmented Quad Gutter

Segmented
Quad Gutter

Corner Flashings

A folded piece of steel used for waterproofing wall sheeting where two walls meet to form an external corner. When used with steel sheet walling it should lap at least one rib and a recommended two ribs to ensure maximum water proofing.

Flashings Roof Flashing Corner

40

Flashings Roof Flashing Standard Drawing Standard Corner Flashing

Standard Corner Flashing

41

Flashings Roof Flashing Standard Drawing Square Corner Flashing

Square Corner Flashing

42

Flashings Roof Flashing Standard Drawing Offset Corner Flashing

Offset Corner Flashing

43

Flashings Roof Flashing Standard Drawing Modified Corner Flashing

Modified Corner Flashing

44

Flashings Roof Flashing Standard Drawing Standard Internal Corner Flashing

Standard Internal
Corner Flashing

45

Flashings Roof Flashing Standard Drawing Internal Corner With Internal Squash Fold

Internal Corner With
Internal Squash Fold

46

Flashings Roof Flashing Standard Drawing Internal Corner With External Squash Fold

Internal Corner With
External Squash Fold

47

Flashings Roof Flashing Standard Drawing Bulky Corner Flashing

Bulky Corner Flashing

48

Flashings Roof Flashing Standard Drawing Stepped Corner Flashing

Stepped Corner Flashing

Apron Flashings

A folded piece of steel used to prevent water from penetrating the space where a vertical surface intersects a roof. Where used with steel sheet roofing it should lap at least one rib and a recommended two ribs for maximum water proofing. Wider apron flashings are advised when the base of the flashing faces into the prevailing wind.

Flashings Roof Flashing Apron

49

Flashings Roof Flashing Standard Drawing Apron Flashing

Apron Flashing

50

Flashings Roof Flashing Standard Drawing Apron Flashing With 90° Turndown

Apron Flashing
With 90° Turndown

51

Flashings Roof Flashing Standard Drawing Apron Flashing With Pole Plate And 135° Break

Apron Flashing With
Pole Plate And 135° Break

52

Flashings Roof Flashing Standard Drawing Apron Flashing With Pole Plate And 90° Break

Apron Flashing With
Pole Plate And 90° Break

53

Flashings Roof Flashing Standard Drawing Apron Flashing With Splayed Pole Plate

Apron Flashing With
Splayed Pole Plate

54

Flashings Roof Flashing Standard Drawing Side Flashing With Pole Plate

Side Flashing
With Pole Plate

Foot Moulds

A folded piece of steel used to finish the base of a vertical surface, in such a way as to prevent water penetration. It also provides an edge to an adjoining soffit. Typical applications are in facades and to finish overhanging canopies. The flashing also prevents water contact to the ends of sheeting.

Flashings Roof Flashing Foot Mould

55

Flashings Roof Flashing Standard Drawing Standard Foot Mould

Standard Foot Mould

56

Flashings Roof Flashing Standard Drawing Foot Mould With Squashfold

Foot Mould With Squashfold

57

Flashings Roof Flashing Standard Drawing Square Foot Mould

Square Foot Mould

Pole Plate Flashings

A purpose made flashing used to seal the join between the end of a roof and masonry wall. A “V” groove end locates into either a preformed reglet, or a cut in the masonry wall providing a water resistant join to the roof and wall connection. When installed, pole plate flashings (often called chimney flashings) can either be stepped to conform to brick courses or left straight, for a more modern appearance.

Flashings Roof Flashing Pole Plate

58

Flashings Roof Flashing Standard Drawing Pole Plate Flashing

Pole Plate Flashing

59

Flashings Roof Flashing Standard Drawing Pole Plate Flashing With 90° Break

Pole Plate Flashing
With 90° Break

60

Flashings Roof Flashing Standard Drawing Pole Plate Flashing With 135° Break

Pole Plate Flashing
With 135° Break

Sill Flashings

A steel sheet used to cap building framework and external brickwork at the base of a window or door frame. It also prevents water from pooling in these areas.

Flashings Roof Flashing Sill

61

Flashings Roof Flashing Standard Drawing Sloping Sill Flashing

Sloping Sill Flashing

62

Flashings Roof Flashing Standard Drawing Square Sill Flashing

Square Sill Flashing

63

Flashings Roof Flashing Standard Drawing Square Sill Flashing With Return

Square Sill Flashing
With Return

64

Flashings Roof Flashing Standard Drawing Z Flashing With Offset

Z Flashing With Offset

65

Flashings Roof Flashing Standard Drawing Plain Sill Flashing

Plain Sill Flashing

66

Flashings Roof Flashing Standard Drawing Sill Flashing With Drip Edge

Sill Flashing
With Drip Edge

Ridge Flashings

A steel covering over the ridge to provide a continuous cover and effective weather seal between two slopes. The size of the edge break should conform with the rib height of the steel roofing to which the ridge is attached. Good roofing practice is to notch this edge break to neatly fit around each rib of the roof sheet.

Flashings Roof Flashing Ridge

67

Flashings Roof Flashing Standard Drawing Cover Flashing

Cover Flashing

68

Flashings Roof Flashing Standard Drawing 3 Break Ridge Flashing

3 Break
Ridge Flashing

69

Flashings Roof Flashing Standard Drawing Raised Top Ridge

Raised Top Ridge

Chimney Flashings

A folded steel sheet commonly used to provide a weather sealed base around chimneys to prevent water penetration. It is often made as a two piece flashing to provide flexibility in installation.

Flashings Roof Flashing Chimney

70

Flashings Roof Flashing Standard Drawing Standard Chimney Flashing

Standard
Chimney Flashing

71

Flashings Roof Flashing Standard Drawing Chimney Flashing With Splay

Chimney Flashing
With Splay

72

Flashings Roof Flashing Standard Drawing Chimney Flashing With Outfold

Chimney Flashing
With Outfold

73

Flashings Roof Flashing Standard Drawing Chimney Flashing With Pole Plate

Chimney Flashing
With Pole Plate

74

Flashings Roof Flashing Standard Drawing Chimney Flashing With Box Gutter

Chimney Flashing
With Box Gutter

75

Flashings Roof Flashing Standard Drawing Chimney Flashing And Cap

Chimney Flashing
And Cap

Parapet Capping

A covering used to waterproof and cap the ends of vertical sheets or masonry walls. A stiffening edge or break is often applied to the legs of the parapet cap for a more appealing appearance, and to minimise oilcanning of the steel. Ensure that these recommendations are taken into account when measuring the flashing. It is also important to ensure that water does not pool on top of the cap, to prevent water seeping into the building.

Flashings Roof Flashing Parapet Capping

76

Flashings Roof Flashing Standard Drawing Standard Parapet Capping With Chamfer

Standard Parapet
Capping With Chamfer

77

Flashings Roof Flashing Standard Drawing Standard Parapet Capping

Standard
Parapet Capping

78

Flashings Roof Flashing Standard Drawing Standard Parapet Capping With Return Hooks

Standard Parapet Capping
With Return Hooks

79

Flashings Roof Flashing Standard Drawing Parapet Capping With Fold One Side

Parapet Capping
With Fold One Side

80

Flashings Roof Flashing Standard Drawing Parapet Capping With Hook One Side

Parapet Capping
With Hook One Side

81

Flashings Roof Flashing Standard Drawing Parapet Capping With Hook And Overflashing

Parapet Capping With
Hook And Overflashing

82

Flashings Roof Flashing Standard Drawing Parapet Cap With ´V´ Both Sides

Parapet Cap With
´V´ Both Sides

83

Flashings Roof Flashing Standard Drawing Parapet Cap with ´V´ One Side

Parapet Cap with
´V´ One Side

84

Flashings Roof Flashing Standard Drawing Combined Parapet And Apron Flashing

Combined Parapet
And Apron Flashing

85

Flashings Roof Flashing Standard Drawing Angled Combined Parapet And Apron Flashing

Angled Combined Parapet
And Apron Flashing

86

Flashings Roof Flashing Standard Drawing Angled combined Parapet And Apron With 90° Break

Angled combined Parapet
And Apron With 90° Break

87

Flashings Roof Flashing Standard Drawing Combined Parapet And Apron With break

Combined Parapet
And Apron With break

Barge Capping

A folded sheet used to waterproof the junction between a fascia or barge board and roof sheeting. The size of the edge break should conform with the rib height of the steel roofing to which the ridge is attached.

Flashings Roof Flashing Barge Capping

88

Flashings Roof Flashing Standard Drawing Standard Square Barge Cap

Standard Square
Barge Cap

89

Flashings Roof Flashing Standard Drawing Standard Barge Cap With 90° Break

Standard Barge
Cap With 90° Break

90

Flashings Roof Flashing Standard Drawing Barge With Hook But No Break

Barge With Hook
But No Break

91

Flashings Roof Flashing Standard Drawing Barge With Hook

Barge With Hook

92

Flashings Roof Flashing Standard Drawing Barge With ´V´

Barge With ´V´

93

Flashings Roof Flashing Standard Drawing Angled Barge With 90° Break

Angled Barge
With 90° Break

94

Flashings Roof Flashing Standard Drawing Angled Barge With 135° Break

Angled Barge With
135° Break

95

Flashings Roof Flashing Standard Drawing Garage Barge

Garage Barge

96

Flashings Roof Flashing Standard Drawing Square Top Barge

Square Top Barge

97

Flashings Roof Flashing Standard Drawing Square Top Barge With 90° Break

Square Top Barge
With 90° Break

98

Flashings Roof Flashing Standard Drawing Square Top Barge With Drip Edge

Square Top Barge
With Drip Edge

99

Flashings Roof Flashing Standard Drawing Simple Barge With 90° Break

Simple Barge
With 90° Break

Miscellaneous Flashings

100

Flashings Roof Flashing Standard Drawing Overcap

Overcap

101

Flashings Roof Flashing Standard Drawing Standard Back Channel

Standard Back Channel

102

Flashings Roof Flashing Standard Drawing Fascia Capping

Fascia Capping

Become a Super Saver

Change Location

Please enter a valid postcode